hidden pixel

Commodore 128 Information

The Commodore 128 (C128, CBM 128, C=128) home/personal computer was the last 8-bit machine commercially released by Commodore Business Machines (CBM). Introduced in January 1985 at the CES in Las Vegas, it appeared three years after its predecessor, the bestselling Commodore 64. The primary hardware designer of the C128 was Bil Herd, who had worked on the earlier Plus/4.

Contents

Technical overview

Original Commodore 128 box

The C128 was a significantly expanded successor to the C64 and unlike the Plus/4, nearly full compatibility with the C64 was retained, in both hardware and software. The new machine featured 128 KB of RAM, in two 64 KB banks and an 80-column RGBI video output (driven by the 8563 VDC chip with 16 KB dedicated video RAM), as well as a substantially redesigned case and keyboard, which included four cursor keys (previous Commodores had two, which required using the shift key to move the cursor up or left. These were retained on the 128, for C64 compatibility), an Alt key, Help key, Esc key, Tab key (not present on prior models) and a numeric keypad. The lack of a numeric keypad, Alt key and Esc key on the C-64 were an issue with some CP/M productivity software when used with the 64's Z-80 cartridge. Many of the added keys matched ones present on the IBM PC's keyboard. While the 128's 40 column mode closely duplicated that of the C64, an extra 1K of color RAM was made available to the programmer, as it was multiplexed through memory address 1. The 128's power supply was vastly improved over the 64's unreliable design, being much larger and equipped with cooling vents and a replaceable fuse. Instead of the single 6510 microprocessor of the C64, the C128 incorporated a two-CPU design. The primary CPU, the 8502, was a slightly improved version of the 6510 capable of being clocked at 2 MHz. The second CPU was a Zilog Z80 which was used to run CP/M software, as well as to initiate operating mode selection at boot time. The two processors could not run concurrently, thus the C128 was not a multiprocessing system.

The C128 had three operating modes: C128 Mode (native mode), which ran at 1 or 2 MHz with the 8502 CPU and had both 40- and 80-column text modes available; CP/M Mode, which used the Z80 in either 40- or 80-column text mode; and C64 Mode, which was nearly 100 percent compatible with the earlier computer. Selection of these modes was implemented via the Z80 chip. The Z80 controls the bus on initial boot-up and checks to see if there are any C64/C128 cartridges present, and if the Commodore key (C64-mode selector) is active on boot-up. Based on what it finds, it will switch to the appropriate mode of operation.

The C128's complex[1][2] architecture includes four differently accessed kinds of RAM (128 kB main RAM, 64 kB VDC Video RAM, 2 kNibbles VIC-II Color RAM, 2 kB floppy drive RAM, 128 or 512 kB REU RAM), two CPUs (main 8502, Z80 for CP/M; the 128D also incorporated a 6502 in the disk drive) and two different video chips (VIC-IIe and VDC) for its various operational modes.[3][4]

C128 Mode

C128 Main board

While the C64's graphics and sound capabilities were generally considered excellent, the response to the Plus/4, which was perceived by the Commodore press as a follow-on model, was that of disappointment. Repeated recommendations were made for a new computer called the "C-128" with increased RAM capacity, an 80-column display as was standard in business computers, a new BASIC programming language that made it easy for programmers to use the computer's graphics and sound without resorting to PEEK and POKEs, a new disk drive that improved upon the 1541's abysmal transfer rate, as well as total C-64 compatibility[5][6]

The designers of the C128 succeeded in addressing most of these concerns. A new chip, the VDC, provided the C128 with an 80-column color CGA-compatible display (also called RGBI for red-green-blue plus intensity). The new 8502 microprocessor was completely backward-compatible with the C64's 6510, but could run at double the speed if desired. However, the VIC-II chip which controlled the 40-column display could not operate at the faster clock rate, so the 40 column display appears jumbled in FAST mode. The C64's BASIC 2.0 was replaced with BASIC 7.0, which included keywords designed specifically to take advantage of the machine's capabilities. A sprite editor and machine language monitor were added. The screen editor part of the Kernal was further improved to support a rudimentary windowing feature and was relocated to a separate ROM. In 80-column mode the editor took advantage of VDC features to provide blinking and underlined text, activated through escape codes.[1] A hardware reset button was added to the system.

Two new disk drives were introduced in conjunction with the C128, the short-lived 1570 and the 1571. Later on, the 3.5 inch 1581 was introduced. All of these drives were more reliable than the 1541 and promised much better performance via a new "burst mode" feature. The 1581 drive also had more on-board RAM than its predecessors, making it possible to open a larger number of files at one time. BASIC 7.0 included DLOAD and DSAVE commands to support loading and saving to disk without using the ",8" device number, and also a DIRECTORY command that read a disk's catalog information directly to screen memory without overwriting BASIC memory as in BASIC 2.0.

The C128 also had twice the RAM of the C64, and a far higher proportion was available for BASIC programming, due to the new MMU bankswitching chip. This allowed BASIC program code to be stored separately from variables, greatly enhancing the machine's ability to handle complex programs, speeding garbage collection and easing debugging for the programmer. An executing program could be STOPped, variable values inspected or altered in direct mode, and program execution resumed using BASIC's GOTO command.

The 128's ROM contained an easter egg: Entering the command "SYS 32800,123,45,6" in native mode reveals a 40-column screen with a listing of, and a message from, the machine's main developers. Also, entering the keywords QUIT or OFF will produce an "?UNIMPLEMENTED COMMAND ERROR". These commands are holdovers from the BASIC interpreter intended for a planned but never produced LCD-display portable computer and were intended to exit from the BASIC interpreter and to ignore keyboard input during sensitive program execution, respectively.

The C128's greater hardware capabilities, especially the increased RAM, screen display resolution, and serial bus speed, made it the preferred platform for running the GEOS graphical operating system.[who?]

CP/M Mode

Using CP/M mode required use of a boot diskette

The second of the C128's two CPUs was the Zilog Z80, which allowed the C128 to run CP/M. The C128 was shipped with CP/M 3.0 (aka CP/M Plus, which was backward compatible with CP/M 2.2) and ADM31/3A terminal emulation. A CP/M cartridge had been available for the C64, but it was expensive and was limited to software on Commodore-formatted disks. To make a large application software library instantly available at launch, the Commodore 128 CP/M and accompanying 1571 floppy disk drive was designed to run almost all Kaypro-specific CP/M software without modification. Unfortunately, the C128 ran CP/M noticeably slower than most dedicated CP/M systems, as the Z80 processor ran at an effective speed of only 2 MHz (instead of the more common 4 MHz), and because it used CP/M 3.0, whose complexity made it inherently slower than the earlier, more widespread, CP/M 2.2 system. From the source code of the C128 CP/M implementation, it is clear that the engineers originally planned to make it possible to run CP/M in the "fast" mode as well, with the 40-column output turned off and the Z80 running at an effective 4 MHz; however, this feature did not correctly function on the first generation C128 hardware.

An unusual feature of the C128 among CP/M systems was that some of the low-level BIOS services were executed by the 8502 instead of the Z80. The latter transferred control to the 8502 after having placed the pertinent parameter values in designated memory locations. The Z80 then turned itself off, being awoken by the 8502 at completion of the BIOS routine, with status value(s) available in RAM for inspection.

CP/M mode was very different from the operating environments Commodore users had become familiar with. While Commodore DOS was built into the ROM of Commodore disk drives, CP/M required the use of a boot diskette and CP/M programs lacked the broad graphics support and user-friendly nature of most Commodore applications. Perhaps because of this, CP/M was possibly the least-used of the 128's three operating modes. Intended to give the new computer a large library of professional-grade business software that Commodore lacked, CP/M was long past its prime by the time of the 128's introduction.

C64 Mode

By incorporating the original C64 BASIC and kernal ROMs in their entirety (16 KB total), the C128 achieved almost 100 percent compatibility with the Commodore 64. The C64 mode can be accessed in one of three ways:

Grounding the cartridge port's /EXROM and/or /GAME lines will cause the computer to automatically start up in C64 mode. This feature faithfully duplicates the C64 behavior when a cartridge (such as Simons' BASIC) is plugged into the port and asserts either of these lines, but unlike the C64, where the Memory-map changing action of these lines is implemented directly in hardware, the C128's Z80 firmware startup code polls these lines on power-up and then switches modes as necessary. C128 native mode cartridges are recognized and started by the kernal polling defined locations in the memory map.

C64 mode almost exactly duplicated the features of a hardware 64; many of the 128's additional features were disabled or unavailable in this mode. The 80 column display, fast mode, MMU, and BASIC 7.0 were not available in 64 mode. The 4 cursor keys at the top of the keyboard were unrecognized, forcing the user to use the 64's cumbersome shifted key arrangement, which were included at the bottom of the 128 keyboard. Also ignored were the 128's numeric keypad and added top-row keys (the only top row keys that were functional in 64 mode were the f1-f8 keys above the keypad.) Some of these features could be turned back on by user software but most commercial programs would ignore them at best, or be completely nonfunctional with these user "wedge" programs in memory.

Some of the few C64 programs that fail on a C128 run correctly when the CAPS LOCK key is pressed down (or the ASCII/National key on international C128 models). This has to do with the larger built-in I/O port of the C128's CPU. Whereas the SHIFT LOCK key found on both C64 and C128 is simply a mechanical latch for the left SHIFT key, the CAPS LOCK key on the C128 can be read via the 8502's built-in I/O port. A few C64 programs are confused by this extra I/O bit; keeping the CAPS LOCK key in the down position will force the I/O line low, matching the C64's configuration and resolving the issue.

A handful of C64 programs wrote to $D030 (53296), often as part of a loop initializing the VIC-II chip registers. This memory-mapped register, unused in the C64, determined the system clock rate. Since this register was fully functional in C64 mode, an inadvertent write could scramble the 40-column display by switching the CPU over to 2–MHz, at which clock rate the VIC-II video processor could not produce a coherent display. Fortunately, few programs suffered from this flaw. In July 1986, COMPUTE!'s Gazette published a type-in program that exploited this difference by using a raster interrupt to enable fast mode when the bottom of the visible screen was reached, and then disable it when screen rendering began again at the top. By using the higher clock rate during the vertical blank period, standard video display was maintained while increasing overall execution speed by about 20 percent.[7][8]

An easy way to differentiate between a genuine C64 and a C128 operating in C64 mode, typically used from within a running program, is to write a value different from $FF (255) to memory address $D02F (53295), a register which is used to decode the extra keys of the C128 (the numerical keypad and some other keys). On the 64 this memory location will always contain the value $FF no matter what is written to it, but on a C128 in 64 mode the value of the location—a memory-mapped register—can be changed. Thus, checking the location's value after writing to it will reveal the actual hardware platform.

RAM setup

To handle the relatively large amounts of ROM and RAM, tenfold the 8502's 64 KB address space, the C128 used the 8722 MMU chip to create different memory maps, in which different combinations of RAM and ROM would appear according to bit patterns written into the MMU's confguration register at memory address $FF00.

Commodore's RAM Expansion Units utilized an external DMA controller to read and write one or more bytes (up to entire ranges of bytes) between the C-128's RAM and the RAM in the expansion unit.

Another feature of the memory management unit was to allow relocation of Zero page and the Stack, which, thanks to the Direct Page register.

Commodore 128D

Late in 1985, Commodore released to the European market a new version of the C128 with a redesigned chassis. Called the Commodore 128D, this new European model featured a plastic chassis with a carrying handle on the side, incorporated a 1571 disk drive into the main chassis, replaced the built-in keyboard with a detachable one, and added a cooling fan. The keyboard featured two folding legs for changing the typing angle.

In the latter part of 1986, Commodore released a version of the C128D in North America and Europe referred to as the C128DCR ("cost reduced"). The DCR model featured a stamped steel chassis in place of the plastic version of the C128D (with no carrying handle), a modular switching power supply similar to that of the C128D, as well as a removable keyboard and internal 1571 floppy drive. On the mainboard, Commodore consolidated some of the components to save production costs and replaced the 8563 video controller with the more technically advanced MOS Technology 8568 (which was also fitted to a few D-models). As a cost-saving measure, the cooling fan that was fitted to the D model was removed, although the mounting provisions on the power supply subchassis were retained.

Inside, the C128DCR ROMs, the "1986 ROMs," so-named from the copyright date displayed on the startup screen, contained several bug fixes—including an infamous one where the 'Q' character would remain lowercase when CAPS LOCK was active—and the 8568 VDC was equipped with 64 KB of video RAM—the maximum addressable amount, equal to four times that of the original C128. The increase in video RAM made it possible, among other things, to generate higher-resolution graphics with a more flexible color palette, although little commercial software took advantage of this capability.

Despite the improvement in the RGB video capabilities, Commodore did not enhance BASIC 7.0 with the ability to manipulate RGB graphics. Driving the VDC in graphics mode continued to require the use of calls to screen editor ROM primitives (or their assembly language equivalents), or by using third-party BASIC language extensions. The most popular such toolkit was Free Spirit Software's "BASIC 8", which added high-resolution VDC graphics commands to BASIC 7.0. BASIC 8 was available on two disks (editor disk and runtime disk) and with a ROM chip for installation in the C128's internal Function ROM socket.

Market performance

Because the C128 would run virtually all C64 software, and because the next-generation, 32/16-bit home computers, primarily the Commodore Amiga and Atari ST, were gaining ground, relatively little software for the C128's native mode appeared (probably on the order of 100–200 fully commercial titles, plus the usual share of public domain and magazine type-in programs). While the C128 sold a total number of 4 million units between 1985 and 1989, its popularity paled in comparison to that of its predecessor. This has been blamed on the lack of native software and on Commodore's less-aggressive marketing, which was mostly focused on the Amiga by this time.[citation needed] An additional explanation may be found in the fact that the C64 sold huge numbers to people primarily interested in computer games, which the more expensive C128 didn't add much value towards improving. A few Infocom text adventures took advantage of the 80 column screen and increased memory capacity, and a very few C64 games were ported to native mode like Kikstart 2 and The Last V8 from Mastertronic and Ultima V from Origin Systems, but the vast majority of games ran in 64 mode. The C128 was certainly a better business machine than the C64, but not really a better gaming machine, and people who wanted business machines bought IBM PC clones almost exclusively by the time the C128 was released. With its advanced BASIC programming language, CP/M compatibility and "user-friendly" native software packages such as Jane, Commodore attempted to create a low-end business market for the 128, even branding it a "Personal Computer" on the case, but this strategy was not successful in the face of contemporary low-cost IBM-compatibles like the Leading Edge Model D and Tandy 1000 that, in some cases, sold for less than a complete 128 system. There was a professional-level CAD program, Home Designer by BRiWALL,[9] but again, most of this work was done on PCs by the 128s era. The main reason that the C128 still sold fairly well was probably that it was a much better machine for hobbyist programming than the C64.

Also, when the C128(D/DCR) was discontinued in 1989, it was reported to cost nearly as much to manufacture as the Amiga 500, even though the C128D had to sell for several hundred dollars less to keep the Amiga's high-end marketing image intact.

Bil Herd has stated that the design goals of the 128 did not initially include 100% compatibility with the C64; some form of compatibility was always intended after Herd was approached at the Plus/4's introduction by a woman who was disappointed that the educational software package she had written for the C-64 would not run on Commodore's new computer. Later, Commodore's marketing department demanded total compatibility. Herd gave the reason for the 128's inclusion of a Z-80 processor as to ensure this 100% compatibility claim, since supporting the 64's Z-80 cartridge would have meant the 128 supplying additional power to the cartridge port. He also stated that the VDC video chip and Z80 were sources of trouble during the machine's design. Herd added that "I only expected the C128 to be sold for about a year, we figured a couple of million would be nice and of course it wouldn’t undercut Amiga or even the C64"[10]

Reliability concerns

Early versions of the C128 occasionally experienced temperature-related reliability issues due to the use of an electromagnetic shield over the main circuit board. The shield was equipped with fingers that contacted the tops of the major chips, ostensibly causing the shield to act as a large heat sink. A combination of poor contact between the shield and the chips, the inherently limited heat conductivity of plastic chip packages, as well as the relatively poor thermal conductivity of the shield itself (which was made from mu-metal), resulted in overheating and failure in some cases. The SID sound chip was particularly vulnerable in this respect. The most common remedy was to remove the shield, which Commodore had only added in order to comply with FCC radio frequency regulations.

The Commodore 128's BASIC 7.0, the programming language which comes built-in with the computer, can be crashed or cause the computer to reboot by executing PRINT""+-0. This bug is present in all 8-bit Commodore machines.[11]

Specifications

See also

References

  1. ^ "The Commodore 128: The Most Versatile 8-Bit Computer Ever Made". http://www.commodore.ca/products/128/Commodore_128.htm.
  2. ^ "TPUG newsletter Feb. 1985". http://www.commodore.ca/gallery/announcements/128_lcd_announcement_TPUG_Feb_1985.pdf.
  3. ^ http://oldcomputers.net/c128d.html
  4. ^ http://www.datasalen.se/Utstallning/Data/CBM/commodore128deng.htm
  5. ^ "Plus/4 and C-16: Disappointingly Mediocre". http://www.commodore.ca/gallery/magazines/misc/Plus_4_C-16_Disappointing_TPUG_Feb_1985.pdf. "I see the Plus/4 as an insult and a disappointment, as well as a major marketing error. One would hope that Commodore will soon come to their senses and put out a `64/Plus' with such selling features as 128K of memory, 80 column display option, a better disk drive, and most importantly, complete compatibility with C-64 software and hardware."
  6. ^ "Commodore's port; preview of the Plus 4, the Amiga, and Alphacom printers". http://www.atarimagazines.com/creative/v10n12/216_Commodores_port_preview.php. "So, Commodore, what to do? I well tell you, okay? Take the C64, slap another 64K of bank-switched memory into it and squeeze it into a sexy case. Improve the keyboard by arranging it into a Selectric-style layout and bettering its feel. Take the excellent Basic from the Plus 4 and build it into the new "C128," adding special sprite and SID commands as in Simon's Basic. Keep the directional cursor keys and function keys across the top, as well as the built-in machine language monitor. Return to the port configurations of the past. Make sure all the machine language disks and ROM cartridges designed for the 64 run beautifully on the C128. And price it at $400 list."
  7. ^ jul86-64 ModeSpeed
  8. ^ jul86-64 ModeSpeed
  9. ^ Complete (?) C128 Commercial Program Listing – The Daily Reviewer
  10. ^ In Memory Of The Commodore C128
  11. ^ ftp://eris.giga.or.at/pub/c64/library/hidden.html Commodore Secrets retrieved 2011 Feb 16
  12. ^ Byte. McGraw-Hill. 1986. p. 274. "C-128 CP/M uses both the Z80 and 8502 processors. The Z80 executes most of the CP/M BIOS functions."
Notes

External links

· · List of Commodore microcomputers
6502-based (8-bit) MOS/CBM KIM-1 · PET/CBM · CBM-II (aka B/P series) · VIC-20/VC-20 · C64 · SX-64 · Educator 64 · C16 & 116 · Plus/4 · C128
68000-based (16-bit / 32-bit) Amiga 1000 · Amiga 500 · Amiga 2000 (Amiga 2500) · Amiga 1500 · Amiga CDTV · Amiga CD32 · Amiga 3000 · (Amiga 3000UX · Amiga 3000T) · Amiga 500+ · Amiga 600 · Amiga 1200 · Amiga 4000 · Amiga 4000T
PowerPC Based A1-SE · A1-XE · Micro-A1 · AmigaOne X1000
x86-based Commodore C64x
Wikimedia Commons has media related to: Commodore 128

Categories: Home computers | Personal computers | CBM hardware | Commodore 64

 

The above information uses material from Wikipedia and is licensed under the GNU Free Documentation License.
Some facts may not have been fully verified for accuracy. [Disclaimers]
This page was last archived by our server on Mon Jul 18 02:06:18 2011.
Displaying this page or its contents does not use any Wikimedia Foundation's resources.
The owners of this site proudly support the Wikimedia Foundation.

More Information Results for "Commodore 128"
[Hide]▼
'Commodore 128' Images
[Hide]▲